Blog DIY is a blog web site that have DIY videos
You will need Iris threads of white, yellow and green colors, a hook number 0.7, a green wire, a pedestal for the brooch, a wide-eyed needle.
Mark a 13 PV string for the leaves. Starting from the 3rd of the loop hook, knit 1 stbn, 1 sts, 7 sts, 1 sts sec, 1 sbn (photo 1). Twist the braid and tie the petal around the perimeter with connecting posts (photo 2). In the last loop, knit 2-3 columns so as not to squeeze the canvas.
. The first petal is ready. Without breaking the thread, tie a 13 VP chain for the second petal (photo 3). Apply exactly like the first. Tie 15 sheets total. The result is a pack of 15 elements, in which each petal is partially placed on top of the previous one (photo 5). Connect 1 VP to lift. Tie the bases of the leaves with stbn so that each column fits the left half of one petal with the right half of the previous one (photo 6, 7, 8). You will receive a total of 15 stbn depending on the number of sheets. After finishing strapping, close the part with its petals in a ring and continue weaving stbn, making even falls until the hole in the center is completely closed (photo 9
Repeat five times in the first row: 1 sc - 1 decrease. Second place has 5 falls. Just in case, let me remind you how to make the cuts: put a hook under the two half loops of the previous row, pull the yarn, do not knit, put the hook under the two half loops of the next column, draw the yarn, knit the three loops on the hook. The end side of the threads is the wrong side. do not knit, put a hook under both half loops of the next column, pull the yarn, also knit the three loops on the hook. The end side of the threads is the wrong side. do not knit, put a hook under both half loops of the next column, pull the yarn, also knit the three loops on the hook. The end side of the threads is the wrong side.
Dial 22 VP for the page. Starting from the 3rd of the loop hook, knit 2 stbn, 3 stsn, 10 stsn, 3 stsn, 2 stbn (photo 13). Spread the braid, tie a green wire about 25 cm long to the edge of the piece. Tie the piece around the circumference together with the wire as follows: 2 stbn, 1 pstn, 1 stsn, 2 vp, 1 cn last column; 1 stbn, 1 stsn, 1 stsn, 1 sts2n, 3 vp, 1 joint venture at the base of the last column; At the base of the last column 1 stbn, 1 pstsn, 1 stsn, 1 sts2n, 1 sts3n, 4 vp, cn; At the base of the last column 1 stbn, 1 stsn, 1 stsn, 1 sts2n, 3 vp, cn; 3 stbn, knit 2-3 stbn from the end of the sheet, 3 stbn; Vp, 1 stsn, 1 pstsn, 1 stbn at the base of the chain of 1 stbn, 3 vp, 1 sts2n; Vp, 1 sts2n, 1 stsn, 1 pstsn, 1 stbn at the base of the chain of 1 stbn, 4 vp, 1 sts3n; Vp, 1 stsn, 1 pstsn, 1 stbn at the base of the chain of 1 stbn, 3 vp, 1 sts2n; Vp, 1 stbn, 2 stbn at the base of the chain of 1 stbn, 2 vp, 1 stbn. Following the same principle, tie 2 more leaves of smaller size (shorten the first chain, make the "teeth", in smaller and smaller quantities). Four.
The bud is woven in the same way as a flower, but its petals are shorter (you can mark 10 instead of 13 VP for the first row), thinner (instead of stsn and pstsn stbn), and less of them (13 will be enough).
Medium yellow: 6-12-18. Green Cup: 6-12-18-24. Sew the middle to the sheets. With a piece of wire of about 25 cm sew the circle of the crown from the inside out, hooking some threads (photo 19). Fold the ends together, bend the middle wire.
Put a glass on the stem, plant it on the leaves (photo 21). Attach a green string to the base of the cup and tie the stbn wire handle quite tightly to the desired length (photo 23).
In the process of tying, glue a small leaf to the stem (photo 24). 6.Tie the cup: 6-12-18-24-30-36 (photo 25). Before the last, the sixth, knit 2-3 stbn to hold the handle, glue one sheet, knit 2-3 stbn, lay the last sheet, knit the row to the end.
Tie the ends of the threads inside out with a knot and cut them off. Bend the ends of the wire together and place them in a loop (photo 29). Sew the glass to the leaves. Sew the base of the brooch.